Motorola One Macro is the cheapest Moto One phone yet, with clean software and a unique macro camera for close-up shots. It features a 6.2-inch IPS LCD display, Mediatek MT6771 Helio P70 chipset, 4000 mAh battery, 4GB of RAM, and 64 GB storage. It runs on Android 9.0 Pie out of the box.

On this page, we have shared the download link and guide to install the Motorola XT2016-1 (Motorola One Macro) firmware flash file using the Moto Flash Tool or using the SP Flash tool. Here you will find all stock firmware zip files for all the supported regions with Motorola One Macro XT2016-1.

If you are someone who wants to restore the device back to factory firmware, then this guide is for you. By using this guide, you can fix certain software-related issues such as hard brick, soft brick, WiFi, or Bluetooth issue, fix lag or stutter or even you can downgrade the device anytime.

Motorola One Macro Device Overview

Motorola One Macro was announced in October 2019 which sports a 6.2-inch IPS LCD display with a screen resolution of 720 x 1520 pixels. The device has an aspect ratio of 19:9 and a screen-to-body ratio of 81.3 %.

The device is powered by an Octa-core (4×2.0 GHz Cortex-A73 & 4×2.0 GHz Cortex-A53) with MediaTek Helio P70 (MT6771T) chipset coupled with 4GB of RAM and 64GB of internal storage. It also supports an external memory card with up to 512 GB microSD. The device came out of the box with an Android 9.0 Pie and was backed by a 4000 mAh battery (Non-removable).

As far as the camera is concerned, the device has a triple-camera setup with 13MP + 2MP + 2MP primary sensors and a selfie camera with an 8MP lens. Other connectivity option includes 4G-VoLTE, GPS, Glonass, Bluetooth, Mobile Hotspot, accelerometer, ambient light sensor, gyroscope, proximity sensor, and compass. etc.

Steps to Install Motorola One Macro XT2016-1 Stock Firmware (Flash File)

Now, if you’re ready to flash the stock firmware manually on your Motorola One Macro XT2016-1 device then you need to download the ODIN flash tool, firmware file, and necessary drivers. So, without wasting any more time, let’s get into it.

Pre-Requirements:

  • This ROM is supported for the Motorola One Macro XT2016-1 (lima) variant only.
  • Make sure that your device should be charged at least 50% or higher.
  • You will require a PC or Laptop with a USB Data Cable.
  • We always recommend our readers to take a full data backup of the device for safety purposes.
  • Install Motorola USB Drivers and Rescue and Smart Assistant Tool on your PC
  • Download SP Flash tool

Motorola One Macro XT2016-1 Firmware Flash Files:

Firmware Installation Guide:

Check out the firmware flashing guide below for the Motorola One Macro XT2016-1. First, make sure to install or extract the adb and fastboot tool on your PC. Now enter the bootloader on your device.

Disclaimer:

Step 1. Bootloader Mode

Enter bootloader mode on your phone. To boot first, turn your phone off. Once your device turned off completely, press and hold volume down, and turn it on. You should see the bootloader screen.

Step 2. Connect Your Device to PC:

After booting your Motorola One Macro into bootloader mode, now connect it to the PC using the USB Cable.

Step 3. Download Stock ROM/Firmware:

To get the full ROM, you can use the LMSA or Rescue and Smart Assistant Tool. Download the zip file and copy it to somewhere on your PC. LMSA tool will unzip the file and will remove the zip file you downloaded.

You can also download the full stock ROM from the above download flash file section on this guide.

Step 4. Flashing Guide:

  • Make sure you follow and download all the required files and flash tool on your PC.
  • Make sure to first extract the download flash file zip and rescuetool_jimnyplus_64.zip into one single folder.
  • Open the flash tool exe file to open the SP Flash Tool User Interface
  • Once your load the SP Flash tool UI, Tap on the Download option
  • In the download tab, you have to load both the download agent and the scatter text file in the scatter-loading section.
  • You will find the scatter text file inside the ROM package for most cases, if not, you can create a scatter text file on your own.
  • Once you load the file, click the Download button
  • To start the upgrade process of stock ROM on your Motorola XT2016-1, you need to turn off your device and hold the Volume Down and Volume Up key together and Connect your Phone to PC/Laptop using USB Cable (Keep the Volume Down and Volume Up button until your computer detects the phone.)
  • When the phone connects, your device will start upgrading the stock firmware
  • You need to wait for a few minutes to complete the upgrade process.
  • Once the flashing process completes, you will find a green button which means a successful upgrade.
  • That’s it! You can reboot your Motorola XT2016-1

Follow our full-depth video guide below:

Guide to Install Stock ROM using SP Flash tool – Video Tutorial

That’s it, guys. We hope this guide was helpful to you. Feel free to ask in the comment below for additional queries.

Advertisement